Govee H5040+H5054 Water Detector with WiFi Gateway User Manual - Manuals+ (2023)

Govee H5040+H5054 Water Detector with WiFi Gateway

At a Glance

Govee Water Leak Detector is a device that sounds an alarm once detecting water drip or leak. Connecting to Wi-Fi via the gateway, it instantly sends you alert notifications of water leaking by app or email whether you are at home or outside.
• 433 is a communication protocol with a frequency of 433MHz.

Wi-Fi Gateway

• Wi-Fi Pairing Button: Connect the gateway to Wi-R.
• 433 Pairing Button: Connect the gateway to the water leak detector.
• LED Indicator: Show status of the gateway.

Water Leak Detector

• Sensor Contact: Detect water drip.
• Sensor Probe: Detect water leak.
• Push Button: Pause alarm I Adjust volume.
• Batteries: 2 X AAA Battery.

Packing List

Checking the Water Leak Detector

1. Insulation sheet removal.
2. Press the button and the detector beeps 1 later, indicating it works well. If not, please open the back cover via a PHOO/PHO screwdriver ta replace new batteries.
3. Adjust alarm volume by pressing the button twice within 1s and the indicator will flash quickly. The volume level Cl* cycles through HIGH – MEDIUM – LOW – MUTE, and def ault volume is high.
4. The detector will alarm if you drip some water on the sensor contact or put it on the surface with water.
5. Press the Push Button ta stop alarm far 5s. Remove the device from water and wipe it up ta stop alarm completely.
6. Notice, When the battery is low, the device sounds “dididi” and flash red slowly.

Installing Your Device

1. Plug the gateway into a power ou~et;
2. Lay the water leak detector flat.
   Notice: Keep distance between the gateway and the detector less than 60m/197ft.

Preparation Before Connecting

1. A Wi-Fi router supporting the 2.4GHz (NOT SGHz)and 802.11 b/gfn bands.
2. Notice: Most of 5GHz routers can also be set to 2.4GHz band or dual band.)
3. Make sure Wi-Fi name and password are correct.
4. A smartphone or tablet supporting 2.4GHz network.
5. Download the app named Govee Home from the App Store ( iOS devices) or Google Play (Android devices).

Connecting to a Wi-Fi Network

1. Connect your phone to 2.4GHz network; Notice, Android device users should tum on Location and iOS users should tap Setting – Govee Home – Location – Always in your phone.
2. Open Govee Home, tB p “+” icon in the top right corner and select “H5040”;
3. Press and hold Wi-Fi Pa iring Button” I II – for 3s.The gateway will get ready to connect to Wi-Fi when the indicator flashes blue slowly;
4. Follow on-screen Instructions In the app to complete the connection;
5. Connected to WI-Fl successfully. The indicator keeps solid blue and you can find the water leak detector In the device 11st;
   Notice: If you cannot flnd the detector, please swipe dawn the device list page to refresh or refer to “Add or Re-add Water Leak Detector” below to add the detector.
6. The indicator keeps solid red if it failed to connect to Wi-Fi; Please check the above steps an~;,in; or you can select “H5040” In the app and tap “Video Guide” for more Instructions.

Notification Setting

App notification: Open the app, select-water leak detector” in the device list, and tap the setting icon in the tap right corner.

Email notification: Open app, and tap “My Profile” .& in the lower right corner — “Notification settings”.

Add or Re-add Water Leak Detector

Notice: The detector is added by default when the gateway connects to Wi-Fi successfully.

• Press the 433 Pairing Button” C!> “and hold for 3s. The gateway will get ready to pair when the indicator flashes red and blue alternately;
• Put the detector nearby the gateway. Press the Push Button and the detector will send pairing signal;
• This is gateway to receiving Signal
  
• The gateway has paired with the water leak detector;
• Swipe down the device 11st page In app to refresh and you can find the new-added device;
  Notice:
• If the gateway fails to pair to the detector in 30s, its indicator will flash blue quickly and it will exit the pairing mode.
• There’s 1 s delay for beep sound after you press the Push Button.
• Please check the above steps and try again If pairing falls.

Troubleshooting

1. The gat.ewey cannot connect to WI-R. / The connection is unstable.
   1. 5GHznetv.or1<Isnotsupported.Thede.Aceonlysupports2.4GHz.
   2. Check the name of the network and password.
   3. Place the gateway within coverage of the router signal.
   4. No obstructions like metal door or wall between t he gateway and the detector are suggested.
2. The water leak detector cannot work.
   1. Pull out the insulation sheet before using.
   2. Open the back cover via a PHOO/PHO screwdriver, remove and re-install the battery.
   3. Check whether the battery is running low.
3. No/Delayed notification in the app.
   1. Make sure that Android device users turn on Location and iOS users select “Setting – Govee Home – Location – Always’ in the phone.
   2. Keep the distance between the gateway and the detector as close as possible.
   3. No obstructions between the gateway and the detector is suggested.
   4. The time interval between two water detection should be longer than 905, otherwise, the app won’t push notification.
   5. Check whether the indicator of the gateway flashes when the detector is triggered. If not, please re-add the detector.

Warning

• Keep devices work temperature within 32″F • 140″F and humidity below 90%RH.
• Do not disassemble devices violently.

Specifications

Customer Service

• Warranty: 12-Month Limited Warranty
• Support: Lifetime Technical Support
• Email; [emailprotected]
• Official Website; www.govee.com

CAUTION:
RISK OF EXPLOSION IF BATTERY 15 IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, incl using interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, 1fnot installed and used in accordance with the instructions may c.ause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful I Interference to radio or television reception, which can be determined by turning the equipment off and on, the user Is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver Is connected.
4. Consult the dealer or an experienced radionic technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.

Documents / Resources